Short-Wave Infrared Colloidal QD Photodetector with Nanosecond Response Times Enabled by Ultrathin Absorber Layers.

Ultrafast short-wavelength infrared (SWIR) photodetection is of great interest for emerging automated vision and spatial mapping technologies. Colloidal quantum dots (QDs) stand out for SWIR photodetection compared to epitaxial (In,Ga)As or (Hg,Cd)Te semiconductors by their combining a size-tunable bandgap and a suitability for cost-effective, solution-based processing. However, achieving ultrafast, nanosecond-level response time has remained an outstanding challenge for QD-based SWIR photodiodes (QDPDs). Here, record 4 ns response time in PbS-based QDPDs that operate at SWIR wavelengths is reported, a result reaching the requirement of SWIR light detection and ranging based on colloidal QDs. These ultrafast QDPDs combine a thin active layer to reduce the carrier transport time and a small area to inhibit slow capacitive discharging. By implementing a concentration gradient ligand exchange method, high-quality p-n junctions are fabricated in these ultrathin QDPDs. Moreover, these ultrathin QDPDs attain an external quantum efficiency of 42% at 1330 nm, due to a 2.5-fold enhanced light absorption through the formation of a Fabry-Perot cavity within the QDPD and the highly efficient extraction (98%) of photogenerated charge carriers. Based on these results, it is estimated that a further increase of the charge-carrier mobility can lead to PbS QDPDs with sub-nanosecond response time.

Topical Application of Deglycating Enzymes as an Alternative Non-Invasive Treatment for Presbyopia.

Presbyopia is an age-related vision disorder that is a global public health problem. Up to 85% of people aged ≥40 years develop presbyopia. In 2015, 1.8 billion people globally had presbyopia. Of those with significant near vision disabilities due to uncorrected presbyopia, 94% live in developing countries. Presbyopia is undercorrected in many countries, with reading glasses available for only 6-45% of patients living in developing countries. The high prevalence of uncorrected presbyopia in these parts of the world is due to the lack of adequate diagnosis and affordable treatment. The formation of advanced glycation end products (AGEs) is a non-enzymatic process known as the Maillard reaction. The accumulation of AGEs in the lens contributes to lens aging (leading to presbyopia and cataract formation). Non-enzymatic lens protein glycation induces the gradual accumulation of AGEs in aging lenses. AGE-reducing compounds may be effective at preventing and treating AGE-related processes. Fructosyl-amino acid oxidase (FAOD) is active on both fructosyl lysine and fructosyl valine. As the crosslinks encountered in presbyopia are mainly non-disulfide bridges, and based on the positive results of deglycating enzymes in cataracts (another disease caused by glycation of lens proteins), we studied the ex vivo effects of topical FAOD treatment on the power of human lenses as a new potential non-invasive treatment for presbyopia. This study demonstrated that topical FAOD treatment resulted in an increase in lens power, which is approximately equivalent to the correction obtained by most reading glasses. The best results were obtained for the newer lenses. Simultaneously, a decrease in lens opacity was observed, which improved lens quality. We also demonstrated that topical FAOD treatment results in a breakdown of AGEs, as evidenced by gel permeation chromatography and a marked reduction in autofluorescence. This study demonstrated the therapeutic potential of topical FAOD treatment in presbyopia.

Chiral liquid crystal based holographic reflective lens for spectral detection.

Flat optics based on chiral liquid crystal (CLC) can be achieved using holographic polarization recording with the help of a photoalignment technique to vary the orientation of the optical axis in a thin CLC layer. A variety of reflective diffractive optical components with high efficiency and polarization selectivity can be realized employing this technique. In this work we discuss the use of CLC diffractive lenses in a spectrometer. The functionalities of two mirrors and a linear grating used in a traditional spectrometer are combined into a single holographic CLC component. Circularly polarized light entering through the slit can be reflected and projected onto a linear detector by the CLC component, with over 90% efficiency. This excellent optical functionality can be achieved with a micrometer thin CLC layer, offering the opportunity for device integration.

Quantum dot lasing from a waterproof and stretchable polymer film.

Colloidal quantum dots (QDs) are excellent optical gain materials that combine high material gain, a strong absorption of pump light, stability under strong light exposure and a suitability for solution-based processing. The integration of QDs in laser cavities that fully exploit the potential of these emerging optical materials remains, however, a challenge. In this work, we report on a vertical cavity surface emitting laser, which consists of a thin film of QDs embedded between two layers of polymerized chiral liquid crystal. Forward directed, circularly polarized defect mode lasing under nanosecond-pulsed excitation is demonstrated within the photonic band gap of the chiral liquid crystal. Stable and long-term narrow-linewidth lasing of an exfoliated free-standing, flexible film under water is obtained at room temperature. Moreover, we show that the lasing wavelength of this flexible cavity shifts under influence of pressure, strain or temperature. As such, the combination of solution processable and stable inorganic QDs with high chiral liquid crystal reflectivity and effective polymer encapsulation leads to a flexible device with long operational lifetime, that can be immersed in different protic solvents to act as a sensor.

Light Modulation in Silicon Photonics by PZT Actuated Acoustic Waves.

Tailoring the interaction between light and sound has opened new possibilities in photonic integrated circuits (PICs) that range from achieving quantum control of light to high-speed information processing. However, the actuation of sound waves in Si PICs usually requires integration of a piezoelectric thin film. Lead zirconate titanate (PZT) is a promising material due to its strong piezoelectric and electromechanical coupling coefficient. Unfortunately, the traditional methods to grow PZT on silicon are detrimental for photonic applications due to the presence of an optical lossy intermediate layer. In this work, we report integration of a high quality PZT thin film on a silicon-on-insulator (SOI) photonic chip using an optically transparent buffer layer. We demonstrate acousto-optic modulation in silicon waveguides with the PZT actuated acoustic waves. We fabricate interdigital transducers (IDTs) on the PZT film with a contact photolithography and electron-beam lithography to generate the acoustic waves in MHz and GHz ranges, respectively. We obtain a V π L ∼ 3.35 V·cm at 576 MHz from a 350 nm thick gold (Au) IDT with 20 finger-pairs. After taking the effect of mass-loading and grating reflection into account, we measured a V π L ∼ 3.60 V·cm at 2 GHz from a 100 nm thick aluminum (Al) IDT consisting of only four finger-pairs. Thus, without patterning the PZT film nor suspending the device, we obtained figures-of-merit comparable to state-of-the-art modulators based on SOI, making it a promising candidate for a broadband and efficient acousto-optic modulator for future integration.

Influence of period and surface anchoring strength in liquid crystal optical axis gratings.

Liquid crystal (LC) based geometric phase optical elements are widely used to effectively change the wavefront or propagation direction of light. Using photoalignment, the liquid crystal can be aligned according to the designed pattern, leading to components such as gratings, lenses or general wavefront shaping devices. The functionality and efficiency of the component is strongly influenced by how well the LC follows the imposed alignment pattern. Next to a considerable tilting of the LC at the air interface, we report on the observation of symmetry breaking in polymerized LC polarization gratings. By carefully analyzing the experimental and numerical data for gratings with different periods, we conclude that the non-negligible homeotropic anchoring strength at the air interface is responsible for the tilt angle and the symmetry breaking. The role of anchoring strength at the photoaligned and air interface and other parameters are investigated.

Ring-shaped liquid crystal structures through patterned planar photo-alignment.

Patterned liquid crystal (LC) configurations find widespread applications in functional devices such as lenses, gratings, displays and soft-robots. In combination with external stimuli such as an applied electric field, photo-alignment at the surfaces offers an attractive way to stabilize different LC structures in the bulk of a device. Herein, a planar LC cell is developed using a photo-alignment layer at the bottom substrate and a rubbed nylon film at the top substrate. Patterned planar photo-alignment is achieved by modulating the linear polarization with a spatial light modulator (SLM) and projecting the pattern onto the bottom substrate. A ring pattern is written into the photo-alignment layer with a continuous rotation between an inner radius and an outer radius. In the other regions the alignment is parallel to the rubbing direction at the top substrate. Four different LC configurations are observed: structure A in which a ring-shaped region is formed with an out of plane (vertical) orientation perpendicular to the substrate, structure B which has a single disclination loop and a 180° twist at the inner region of the photo-patterned ring (r < rin), structure C which has no discontinuities but a 360° twist in the inner region of the photo-patterned ring (r < rin) and structure D with 2 disclination loops. The LC director configuration for all 4 structures is simulated through finite element (FE) Q-tensor simulations and the optical transmission for each structure is simulated using a generalized beam propagation method.

Design, fabrication and characterization of a distributed Bragg reflector for reducing the étendue of a wavelength converting system.

In this work, the design, fabrication and characterization are reported for a distributed Bragg reflector (DBR) filter with a specific wavelength and angular dependency, which aims to improve the light collection from a wavelength-converter-based light source into a smaller angle than the full angle Lambertian emission. The desired design is obtained by optimizing the transmission characteristics of a multi-layer structure. Titania (TiO2) and silica (SiO2) are used as high and low refractive index materials, respectively. The deposition is made by electron beam evaporation without substrate heating, followed by a post-annealing procedure. The optical properties of the evaporated layers are analyzed by ellipsometer and spectrometer measurements. The angular and wavelength dependency of the fabricated DBR is in good agreement with simulations for the designed structure.

Improvement of liquid crystal tunable lenses with weakly conductive layers using multifrequency driving.

A common technique to realize the gradient electric field profile that is required in liquid crystal tunable lenses is the use of a weakly conductive layer. Thanks to this layer, an applied voltage with a certain frequency allows us to obtain a refractive index profile that is required for the lens operation. Due to the limited degrees of freedom, however, it is not possible to avoid aberrations in a weakly conductive layer-based tunable lens for a continuously tunable focal length. In this work, we discuss the use of additional higher frequency components in the voltage signal to reduce the lens aberrations drastically.

Mode coupling by scattering in chiral nematic liquid crystal ring lasing.

Lasing in dye-doped chiral nematic liquid crystal can be realized with low pump energy and relatively high efficiency, thanks to the high reflectivity of the periodic structure. When the helical axis is oriented perpendicular to the substrates, the main lasing peak is normal to the substrates. In some cases, ring lasing of a particular wavelength is observed into an emission cone with axial symmetry. In this paper we explain how scattering of light in the liquid crystal layer leads to optical coupling between normal modes and inclined modes. Based on a numerical model that takes into account spontaneous emission, gain and scattering we show that scattering leads to emission characteristics that are similar to experimental results.

Voltage-controlled formation of short pitch chiral liquid crystal structures based on high-resolution surface topography.

Chiral nematic liquid crystals (CLCs) offer interesting perspectives for device applications and are fascinating materials to study because of their ability to self-assemble into complex structures. This work demonstrates that narrow lines of electron-beam resist on top of an ITO coated glass surface can dramatically influence the formation and growth of short pitch chiral superstructures in the bulk. By applying a voltage to the cell, directional growth of CLC structures along the corrugated surface can be controlled. Below the electric unwinding threshold, chiral structures start to grow along the grating lines with their helical axis parallel to the substrates. This results in a uniform lying helix-like structure at intermediate voltages and a chiral configuration with periodic undulations of the helical axis at low voltages.

Generation of multiple solitons using competing nonlocal nonlinearities.

We discuss the dynamics of fundamental Gaussian beams launched in saturable and nonlocal nonlinear media. Solely in the presence of a self-focusing saturable nonlinearity, the breathing solitons undergo strong deformation. The addition of a defocusing nonlinearity leads to the generation of couples of solitons. Experimentally, we demonstrate in nematic liquid crystals the formation of multiple spatial solitons starting from a bell-shaped input, with both direction and the number of filaments depending on the input power, confirming the theoretical predictions.

Nanophotonic Pockels modulators on a silicon nitride platform.

Silicon nitride (SiN) is emerging as a competitive platform for CMOS-compatible integrated photonics. However, active devices such as modulators are scarce and still lack in performance. Ideally, such a modulator should have a high bandwidth, good modulation efficiency, low loss, and cover a wide wavelength range. Here, we demonstrate the first electro-optic modulators based on ferroelectric lead zirconate titanate (PZT) films on SiN, in both the O-band and C-band. Bias-free operation, bandwidths beyond 33 GHz and data rates of 40 Gbps are shown, as well as low propagation losses (α ≈ 1 dB cm-1). A half-wave voltage-length product of 3.2 V cm is measured. Simulations indicate that further improvement is possible. This approach offers a much-anticipated route towards high-performance phase modulators on SiN.

Complex liquid crystal superstructures induced by periodic photo-alignment at top and bottom substrates.

The formation of nematic liquid crystal (LC) superstructures in cells with non-uniform photo-alignment at the confining substrates is studied experimentally and by simulations. An interference pattern of left- and right-handed circularly polarized light is used to define the alignment at both substrates separately, so that the alignment varies along the x-coordinate on one substrate and along the y-coordinate on the other substrate. The interplay between the complex surface alignment and the liquid crystalline soft matter leads to the formation of interesting 3D configurations. The periodic LC structures that are formed in the bulk of the cell are analyzed experimentally by polarizing optical microscopy (POM) for different applied voltages. In the region with strong photo-alignment at both substrates, a 2D LC polarization grating (PG) with a complex 3D director configuration is formed. Distinct periodic structures with different symmetry properties are observed in the regions with weak illumination at the top and/or bottom substrate. The director configuration in the different regions was successfully simulated with the help of finite element (FE) Q-tensor simulations. The agreement between the simulations and the experiments was verified by comparing the POM images with simulated results for the transmission between crossed polarizers.

Interplay between multiple scattering and optical nonlinearity in liquid crystals.

We discuss the role played by time-dependent scattering on light propagation in liquid crystals. In the linear regime, the effects of the molecular disorder accumulate in propagation, yielding a monotonic decrease in the beam spatial coherence. In the nonlinear case, despite the disorder-imposed Brownian-like motion to the self-guided waves, self-focusing increases the spatial coherence of the beam by inducing spatial localization. Eventually, a strong enhancement in the beam oscillations occurs when power is strong enough to induce self-steering, i.e., in the non-perturbative regime.

Multi-electrode tunable liquid crystal lenses with one lithography step.

Electrically tunable lenses offer the possibility to control the focal distance by applying an electric field. Different liquid crystal tunable lenses have been demonstrated. In order to minimize lens aberrations, multi-electrode designs allow us to fine-tune the applied voltages for every possible focal distance. In this Letter, we provide a novel multi-electrode design in which only one lithography step is necessary, thereby offering a greatly simplified fabrication procedure compared to earlier proposed designs. The key factor is the use of a high-permittivity layer, in combination with floating electrodes.

Reflective liquid crystal hybrid beam-steerer.

We report on efficient optical beam-steering using a hot-embossed reflective blazed grating in combination with liquid crystal. A numerical simulation of the electrical switching characteristics of the liquid crystal is performed and the results are used in an FDTD optical simulator to analyze the beam deflection. The corresponding experiment on the realized device is performed and is found to be in good agreement. Beam deflection angles of 4.4° upon perpendicular incidence are found with low applied voltages of 3.4 V. By tilting the device with respect to the incoming optical beam it can be electronically switched such that the beam undergoes either total internal reflection or reflection with a tunable angle.

Nematicon-driven injection of amplified spontaneous emission into an optical fiber.

We investigate experimentally the interaction between amplified spontaneous emission (ASE) and a soliton, which are both generated in a dye-doped nematic liquid crystal (LC) cell. A light beam is injected through an optical fiber slid into the cell to form a soliton beam. ASE is then automatically collected by this self-induced waveguide and efficiently coupled into the same optical fiber, in the backward direction. We demonstrate that the presence of the soliton improves the ASE collection by one order of magnitude. We also show that the ASE is highly polarized in the plane of the LC cell and that the ASE spectrum depends on the pump stripe orientation with respect to the LC director. The origin of the spectral anisotropy of the gain curves is determined with the help of femtosecond pump-probe spectroscopy.

Ferroelectric thin films with liquid crystal for gradient index applications.

We report on the first ever combination of a thin film of lead zirconate titanate (PZT) with a liquid crystal (LC) layer. Many liquid crystal applications use a transparent conductive oxide to switch the liquid crystal. Our proposed processing does not, instead relying on the extremely high dielectric constant of the ferroelectric layer to extend the electric field from widely spaced electrodes over the liquid crystal. It eliminates almost entirely the fringe field problems that arise in nearly all the liquid crystal devices that use multiple addressing electrodes. We show, both via rigorous simulations as well as experiments, that the addition of a PZT layer over the addressing electrodes leads to a markedly improved LC switching performance at distances of up to 30 µm from the addressing electrodes with the current PZT-layer thickness of 0.84 µm. This improvement in switching is used to tune the focal length of the microlens with electrodes spaced at 30 µm.

Optimization of electrically tunable VCSEL with intracavity nematic liquid crystal.

We optimize the wavelength tuning range of a Vertical-Cavity Surface-Emitting Laser with an intracavity layer of nematic Liquid Crystal (LC-VCSEL) lasing around 1.3 µm. The tunability is obtained by applying voltage to the liquid crystal layer, which esentially is to vary the refractive index from the extraordinary to the ordinary. We achieve 71.6 nm continuous tuning (without mode hopping) with liquid crystal thickness of about 3.2 µm. We investigate the impact of ambient temperature on the LC-VCSEL tuning range and show that mode-hop tuning can be achieved in the temperature range from -10°C to 50°C where the LC is in nematic phase.